Crown Granite Finish Paint

Crown Granite Finish Paint

Product Description

Type: A multi-color stone paint; the final paint will vividly represent natural granite or marble.

Recommended use: Ideal for decorating and protecting interior and exterior walls. Substrates: New or previously painted (sound) plaster, concrete, and cement rendering.

Advantages: Dustproof with self-cleaning properties. High Abrasion and scratch resistance. 10- year warranty. Super weatherproof against rainwater and sun. Resistant to spread of flame. Good colour retention.

Conditions during application: The temperature of the substrate should be a minimum of 10°C and at least 3°C above the dew point of the air, measured near the substrate. Good ventilation is required in confined areas to ensure proper drying.


Colour Range: Over 10 standard shades
Pack Sizes: 20kg.
Finish: Texture
Shelf Life: 12 months if stored under cool and dry conditions.
Thinner & equipment cleaner: Water



No. Procedure Product Coverage Drying time @25oC Recoat time Tools Note
1 Substrate treatment Putty series Fine Putty: 18 – 20m2 per pack @1 – 1.5mm thickness. Touch Dry: 2h ≥4hrs Putty Knife Make the base solid, smooth, dry, and clean
Coarse Putty: 11 – 14 m2 per pack @ 2-4 mm thickness Hard Dry: 48h
2 Granite Undercoat Water base Damp- proof primer/ 6m2/2 Coats Touch Dry: 1h ≥1hr Brush/ roller / sprayer Seal the Substrate, alkali resistance, penetration resistance
Hard Dry: 12h
3 Mix: Granite Bonding Coat + Granite Flakes Granite stone paint 2.25 L /m2 (1L Granite Flake: 1.25 Granite Bonding Coat Touch Dry: 1h ≥24hrs Recommended spray application
by Granite Spray gun
Protect the paint from water after applying.
Hard Dry: 24h
4 Granite Silicone Topcoat Water base Waterpr oof and weather- resistant finish 6 m2/2 Coats Touch Dry: 1h ≥1hr Wool Brush/ roller /sprayer Polish sharp sands or angle before spraying topcoat if necessary

STEP 1 Surface Preparation – Inspect the surface for dampness, effloresces, loose particles
STEP 2 Remove all loosely held particles / old paint by scraper, wire
STEP 3 If Cracks observed on surface Fill all the cracks as below Cracks up to 1.5 mm – Fill with Polyfilla
Cracks above 2mm – Fill concrete + Dr. Fixit
STEP 4 Hairline Cracks / Undulation/Unevenness – Fill by 1 coat of Crown Level Putty (Coarse) 2 to 4mm + 1 coat Crown Walplast Cement Putty (Fine) 1.5 to 2mm. (If surface is free of undulations & loose particle, skip step 2 & proceed with step 5
STEP 5 Apply 2 coats of Granite Undercoat by spray, Brush or Roller
STEP 6 Apply good quality Crown Masking Tapes to make panelling effect on walls, if desired. Or apply finish like normal smooth finish paint
STEP 7 Apply Granite Finish Pain Mix (Mixture of Granite Bonding Coat & Granite Flake in ratio GBC -1.25 L: GF – 1 KG)
STEP 8 Flat the sprayed Crown Granite Texture Mix by plastic/ acrylic trowel
STEP 9 If done panelling effect, then remove the Crown Masking tapes carefully
STEP 10 Apply 2 coats of Granite Topcoats
STEP 11 Allow it to dry for 12 hours
STEP 12 Granite Texture Finish is Ready


Availability: From Crown Depots in Nairobi, Kisumu, Mombasa, Meru, Nyeri, Eldoret, Arusha, Mwanza, Dar es Salaam, Kigali and through Crown Stockists.

Storage Conditions: Store under cool dry conditions away from direct sunlight, heat and extreme cold.

Disclaimer: The recommendations contained herein are given in good faith and meant to guide the user in accordance with good painting practices. They are gained from our tests and experiences and are believed to be accurate and reliable. No warranty/guarantee is implied by the recommendations contained herein since the conditions of use; application method, substrate and cleanliness of the substrate are beyond Crown Paints Kenya PLC control.

Technology may change with time, necessitating changes to this Technical Data Sheet (TDS). Crown Paints Kenya PLC reserves the right to amend the TDS without any further notice.
It is the responsibility of the user to ensure that the latest TDS is being used for reference.

Related Products